Dodge Ram Gen III (3) Tow/Haul Button Replacement - image

Files (11)

All_stock_Dodge_RAM.stl

STL

2.9 MB

Dodge_RAM_Towing_Button.stl

STL

236.7 KB

Haul_button_Brotherhood_of_Steel.stl

STL

288.6 KB

RAM_Stock_BoS_raised.stl

STL

511.5 KB

RAM_stock_Demon_Engraved.stl

STL

490.5 KB

RAM_stock_Demon_Raised.stl

STL

681.1 KB

RAM_Stock_Hellcat_Raised.stl

STL

374.8 KB

RAM_stock_RAMLOGO_Raised.stl

STL

470.6 KB

RAM_stock_RAMLOGO_Raised1.stl

STL

470.3 KB

RAM_Stock_Skull_Raised.stl

STL

635.5 KB

RAM_Stock_Skully_Raised.stl

STL

324.0 KB

Print guidance estimate

Slicer data required

Print cost & setup estimate

Setup guidance plus saved or slicer-confirmed filament, cost, and time. Model file size is never treated as printable volume.

11 model files

Typical selected file

Slice required

Choose the needed variant and slice it; source file size is not printable volume.

Material cost

Slice required

Use the slicer's filament total; STL/3MF byte size is not a cost input.

Print time

Slice required

Slice with the recommended material, infill, orientation, and supports.

STL file	Role	Source size	PETG / ASA 20%	PETG / ASA 25%	100% solid	Recommendation
All_stock_Dodge_RAM.stl	Printable file	2.9 MB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.
Dodge_RAM_Towing_Button.stl	Printable file	236.7 KB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.
Haul_button_Brotherhood_of_Steel.stl	Printable file	288.6 KB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.
RAM_Stock_BoS_raised.stl	Printable file	511.5 KB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.
RAM_stock_Demon_Engraved.stl	Printable file	490.5 KB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.
RAM_stock_Demon_Raised.stl	Printable file	681.1 KB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.
RAM_Stock_Hellcat_Raised.stl	Printable file	374.8 KB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.
RAM_stock_RAMLOGO_Raised.stl	Printable file	470.6 KB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.
RAM_stock_RAMLOGO_Raised1.stl	Printable file	470.3 KB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.
RAM_Stock_Skull_Raised.stl	Printable file	635.5 KB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.
RAM_Stock_Skully_Raised.stl	Printable file	324.0 KB STL	Slice file	Slice file	Slice file	Ensure the print bed is level and clean for optimal adhesion.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Knobs/Buttons

Dodge Ram Gen III (3) Tow/Haul Button Replacement

0 downloads63 views0 likes

Shared by

3DPrintedCarPart

Verified

Description

THIS IS A WORK IN PROGRESS - I've not been able to test it on someone else's Dodge RAM. I built this based on the stock button, so it *should* work... Luckily it's like an hour long print (at the worst) and it doesn't use much material. My truck came without the overdrive/tow/haul button on the shifter. So I made one. If you have yours, then this is a nice custom touch. The blank button's obj file is there if you want to make your own. This is a work in progress. The internal part of the button, looks like it has a square peg that sticks out of it. Mine's broken so I could not test this. It does work with my broken one. I installed a spring (see the gap in the bottom?) because there was a lot of travel, I bet it'll work and there'll just be the right amount of travel. The bezel will come off, you just have to pull one it. This *may* fit the gen II Dakotas and Durangos as well... and maybe some Jeeps (post merger) and possibly some of the mini vans. Dodge likes to recycle parts, so check and see! Also WTF happened to the Durango? It looks like they should have just killed the whole Durango line and labelled the latest generation as the continuation of their minivan line... The remix search on this website doesn't work so here they are: Remixed from: https://www.thingiverse.com/thing:1960406 - Dodge Hellcat https://www.thingiverse.com/thing:2482388 - Dodge Demon Logo https://www.thingiverse.com/thing:4357830 - Dodge RAM Logo https://www.thingiverse.com/thing:326026 - Brotherhood of Steel logo https://www.thingiverse.com/thing:3472948 - Skull (Realistic) https://www.thingiverse.com/thing:3728607 - Skull (cartoon-ish)